Learn to knit a small ring handle bag using a single garter stitch square and a pair of ring handles.
When I was playing with the garter stitch, I discovered that the edging of the garter stitch is great for picking up stitches evenly as the rows are made easily recognizable by the ridges.
A garter stitch fabric only yields 2 sides with ridges. I wondered whether it is possible to create one where all 4 sides have garter ridges. The answer is yes. Knit the garter stitch on a bias. The result of my experiment is this garter stitch metal ring handle bag.
Materials
- 4 ply sock yarn about 400-450 yards in length
- 2 small ring handles
- Fabric for bag lining
- Circular knitting needles – US No.2 or 2.75mm
Gauge and Measurement
My gauge using 2.75mm needles on sock yarn (18wpi) is 28sts / 48 rows = 4 inches in garter stitch.
The weight of the yarn and the size of the needles stated here are what I use for the bag above. They are not carved in stone. You can use yarn in any weight and appropriately sized needles to achieve the gauge you want for your bag. I personally like a tight gauge for bags so that they look and feel sturdy.
The Bag Body
Garter stitch is achieved by knitting every row. The body is a knitted square casting on from one of the 4 corners.
Cast on 1 stitch.
Row 1: KFB (2 stitches)
Row 2: KFB, KTBL (3 stitches)
Row 3: KFB, Knit to last stitch, KTBL (4 stitches)
Repeat Row 3 until you have reached the desired size or length of the bag you want. Or slightly less than 50% of the yarn you have. In my case, I used up 200 yards of yarn.
At this moment, the knitted fabric is a triangle. To make the rest of the body, start decreasing 1 stitch every row.
Row 1: Knit all
Row 2: Knit until last 2 stitches, K2 together through back loop.
Repeat Row 2 until you have only 3 stitches left on your needles. Knit the 3 stitches. Turn the work and slip the first stitch, knit 2 together, and pass the first stitch over. Cut the yarn and pull it through the loop.
Lining
Line the bag with any fabric you fancy, leaving the edge of the knitted piece for picking up stitches later.
Flaps for bag handles
Pick up stitches from between the garter stitch ridges with the right side facing you (the side without the lining). 1 stitch for each ridge for the entire side.
Row 1: Knit all picked stitches
Row 2: Knit 2 together for the entire row
Knit 6 rows.
Handle flap
Row 9: Purl all
Row 10: Knit all
Row 11: Purl all
Row 12: Knit all
Knit 6 rows.
Row 20: *(Knit 1, increase 1), repeat * for the entire row
Row 21: Knit all
Bind off
Repeat the whole set of instructions for the opposite side of the bag.
You should end up with 2 flaps that have a fold in the middle folding down over the lined side.
Securing the handles
Place a ring handle on the fold and fold the flap over the handle and secure the flap to the bag with some tacking pins. Sew the end of the flap securely to the bag using waste yarn and a sewing needle. Do the same for the other flap.
Opening of the bag
Pick up stitches starting from the edge of one handle flap to the other flap.
Knit 1 row across. Knit 2 together for the next row. Bind off
Repeat for the other side.
Weave in all the ends and your bag is ready for use.
Happy knitting!








Leave a comment